Fire Alarm Manual Pull Station Height Code Ontario
Fire Pull Station Height
Fire Alarm Manual Pull Station Height Code California
Fire Alarm Pull Station Height

Fire Alarm Manual Pull Station Height Code

Field Device Installation Guideline (Canada)

Errata: The line item for the “.030 Ampere/16AWG” entry is shown as “150 feet” in Table 5 of the FA-1000 installation manual. We have converted the “229 meter” entry on the line next to it to reflect the corrected Imperial measurement of “751”. End-of-Line Resistors may be mounted in a properly identified common termination box or inside the fire alarm system’s. Requirements for Fire Alarm Systems. Fire alarm pulls must meet the following requirements for operable parts: The pull lever must be operable with one hand. The force to activate the pull lever cannot be greater than five pounds. The pull lever cannot require tight grasping, pinching, or twisting of the wrist. In addition, the pull lever. Aug 29, 2017 Are you talking about the activator, The manual fire pull? According to Section 5.13.4 of NFPA 72, mounting height must be between 3½ and 4½ feet from floor to handle. Section 4.2.5 of the ADA states, “If the clear floor space only allows forward approach to an object, the maximum high forward reach allowed shall be 48 inches. Models F1GT, F1GGT & F1GHT Manual Non-Code Pull Stations Models F1G Manual Non-Code Station Reset To restore an operated station to normal standby condition requires the use of a standard allen-head key. The latch, located just above the nameplate, is turned a quarter turn to the left. This allows the front of the station to swing down.

Additional requirements are outlined in the Standard for Installation of Fire Alarm Systems (CAN/ULC-S524) that is referenced by the current Building Code in effect. Please refer to the applicable Standard for more detailed requirements. This table’s focus is as a convenience guideline for basic wall-mounted device installation heights only. The manufacturer’s installation instructions should be consulted for termination of wiring and approved mounting methods. Notes referenced in the table are provided below.

Fire Alarm Manual Pull Station Height Code Ontario

It is extremely important that the installer review the manufacturer’s instructions that detail the proper installation, mounting, wiring, and termination of the control equipment and field devices to avoid errors that could prove costly!

Please review our terms of use!

Fire Pull Station Height

You can also download the PDF of the Installation Guide!
When printed, it should fit on a single double sided sheet which
you can laminate and carry around as a handy reference!

Field Device Type	CAN/ULC-S524-01/06	CAN/ULC-S524-14
Manual Station	1200 – 1400 mm above the floor measured to the centre of the manual station (the centre of the back-box)	1050 – 1150 mm above the floor measured to the centre of the manual station (the centre of the back-box)
Audible Signalling Appliance	Not less than 2300 mm above the floor (where ceiling heights allow) measured to the centre of the device. Not less than 150 mm from the ceiling measured from the top of the assembled device (top edge of gong if the device is a bell)	Not less than 2300 mm above the floor (where ceiling heights allow) measured to the centre of the device. Not less than 150 mm from the ceiling measured from the top of the assembled device (top edge of gong if the device is a bell)
Insuite Audible Signalling Appliance with Integral Silencing Means	1200 – 1400 mm above the floor measured to the centre of the silencing means (the centre of the back-box does NOT apply)	1050 – 1150 mm above the floor measured to the centre of the silencing means (the centre of the back-box does NOT apply)
Remote Audible Signal Silencing Means	1200 – 1400 mm above the floor measured to the centre of the silencing means (the centre of the back-box does NOT apply)	1050 – 1150 mm above the floor measured to the centre of the silencing means (the centre of the back-box does NOT apply)
Rollercoaster tycoon touch increase shop satisfaction download. Visual Signalling Appliance (Wall Mounted)	Mounted so that the entire lens is not less than 2000 mm and not more than 2400 mm above the finished floor. See Section 5.4.5 for additional criteria.	Mounted so that the entire lens is not less than 2000 mm and not more than 2400 mm above the finished floor. See Section 9.4 for additional criteria.
In-suite Sounder Isolator (See Notes 4, 5)	Installed outside of the suite it is protecting. They shall be visible and accessible at all times.	Installed outside of the suite it is protecting. They shall be visible and accessible at all times.
Fire Fighter’s Telephones	Mounted so that the height from the floor to the centerline of the enclosure is between 1350 mm and 1500 mm.	Mounted so that the height from the floor to the centerline of the enclosure is between 1350 mm and 1500 mm.
Smoke Detector (Wall Mounted)	100 - 300 mm from the ceiling to the top edge of the detector (does NOT apply to the base or backbox)	100 - 300 mm from the ceiling to the top edge of the detector (does NOT apply to the base or backbox)
Heat Detector (Wall mounted in an elevator pit application only) NOTE: There is no requirement for elevator pit fire detection in either NBC 2010 or CAN/CSA B44-2007	Not Addressed	Where specified in the DESIGN or by the local AHJ, detector is to be wall or bracket mounted 300 mm below the lowest point of travel of the cab (measured to the undersurface of the cab floor). Linear heat detection cable is recommended in this application. See the ULC Bulletins page!
Data Loop Isolator	Mounted in accordance with the manufacturer’s instructions, must be visible and accessible at all times. Installed in accordance with Section 5.14. (See Note 5)	Mounted in accordance with the manufacturer’s instructions, must be visible and accessible at all times. Installed in accordance with Section 10.2.1. (See Note 5)
Addressable Modules (Supporting Field Devices) Includes: relay modules, initiating modules, supervised output modules, signal circuit modules	Not Addressed (see Note 6) (Follow manufacturer’s printed installation instructions)	Not Addressed (see Note 6) (Follow manufacturer’s printed installation instructions)
End-of-Line Devices (Resis